What Is Geothermal Energy? Types and Advantages. Why should we care about Geothermal Power Plant?

Geothermal Energy

Image: Vectorjuice -freepik.com

What Is Geothermal Energy? Types and Advantages. Why should we care about Geothermal Power Plant?

Admin 4th February 2021

Geothermal Energy needs an idle resource that holds the potential to meet the electricity and heating demands for the future. Being a renewable and sustainable resource, the harm done to the environment is gradually low. It is carbon-free and provides a perpetual supply of heat. This energy is the affordable solution to reducing dependency on fossils-fuels and global warming. 

What is Geothermal Energy?

Geothermal comes from the Greek word, where ‘Geo’ refers to Earth and ‘Therme’ refers to Heat. The heat procures from the beneath of earth’s crust. Generally, it is found distantly far below the earth’s burning molten rock ‘Magma’ and stored in the rocks and vapor in the center of the earth. In the process of producing power from this energy, wells need to be dug 1.6 miles or more deep into an underground reservoir to obtain the steam and hot water there, which can then be utilized to drive turbines connected to electricity generators.

In-dept, the US Energy Information Administration writes that the planet has four parts of the layer.

  • An inner core of solid iron is about 1,500 miles in diameter

  • Magma is about 1,500 miles thick

  • A magma and rock locating in-depth is almost 1,800 miles thick

  • A crust of rock that forms continents is 15 to 35 miles thick under the continents and 3 to 5 miles thick under the ocean floors

Likewise, scientists have identified that the earth’s internal central depth is about 10,800° F. And the Mantle of magma ranges the temperature from around 392° to approximately 7230° F. The earth's crust fragments into parts called tectonic plates. Magma comes close to the boundaries of these plates, which is where many volcanoes happen. The lava that erupts from volcanoes is noticeably magma. Magma has numerous heat underground by which the Water and rocks absorb heat. Hence, that heat is called geothermal energy.

Trends in Renewable Energy

Source: International Renewable Energy Agency (IRENA)

Moreover, Italian scientist Piero Ginori Conti invented a geothermal electric power plant in 1904 and by now over 20 countries produce this energy. Well, people have been using energy for the culture of bathing in mineral spring, cooking, and eating since the millennium. Also, most Icelanders use this energy to heat their building and water. According to the International Renewable Energy Agency (IRENA), this energy has grown steadily from around 10 GW worldwide in 2010 to 13.3 GW in 2018.

Renewable energy is most likely to never end. Relatively, the underground steam and hot water produced by the decay of radioactive elements within the Earth is a natural resource that is generated for an unlimited time. Furthermore, a recent survey tells that once the storage process is constructed successfully, almost 10% of today’s energy needs can be supported. Hence, this energy is a renewable resource. 

Where does Geothermal Energy Work best?

Preferably, the suitable place that this energy works best is where extensive heat is produced. Out of that, the “Ring of Fire” is an area in the nearby Pacific Ocean that has more Volcanoes than other usual regions on the Earth. Also believed that it experiences regular earthquakes and the frequent eruption of volcanoes. About 90% of the earthquake occurs and 75% of volcanoes are located at Ring of Fire. Its length is approximately 40,000 kilometers (24,900 meters). 

Repeating, Geothermal powers come from the slow decay of radioactive minerals such as Uranium, which causes the rock to become magma. Tectonic plate movement causes the movement of magma up the edges, forming a reservoir in which geothermal steam and hot water can be recovered through wells. These forms of steam or hot water are pressured through a turbine that is connected to a generator that produces electricity. 

Top 10 Geothermal Countries of 2019

Source: ThinkGeoEnergy 

Specifically, the US is the leading producer of this energy across the world with a 3,676 MW of energy and an additional 23 MW to be added soon. Most of the geothermal plants are located in Western states and Hawaii because the resource is close to the earth’s surface. Then comes the top 2 Asian countries securing the largest producing energy source that is Indonesia with 185 MW added on existing 2,133 MW and the Philippines of 1.918 MW. Also, Indonesia owns 4 out of the world’s top 10 geothermal power projects. 

Similarly, Turney appears in 4th position with 1,526 MW. The country’s biggest Power plant project is the Kizildere Geothermal Power Plant with an installed capacity of 95 MW. In New Zealand, 13% of overall electricity is supplied using this energy. The energy is mainly generated from Taupo Volcanic Zone and the country has an installed capacity of 1,005 MW. The South American nation, Mexico, has a capacity of 962.7 MW of energy. However Italy introduced the energy initially, but it lands in the 7th position under the top 10 Geothermal Countries. This is because of the political climate so it has 944 MW of power. 

Next comes the world’s leading country for Safari destination- Kenya. The country is extending its 861 MW with the addition of 193.3 MW power. Next, Iceland obtains 755 MW of power and it is famous for heating the building and water through energy. Lastly, Japan has a total of 601 MW. Also, Japan has a huge potential for this energy after the Fukushima Nuclear Power Accident. The disaster happened in 2011 caused by Tsunami and Earthquake. 

Uses of Geothermal Energy

  • Direct use of Geothermal Heat

This is an easy alternative to get access to hot water but it applies to the areas where hot springs and underground reservoirs are nearest. For that, a production facility, a downhole, and circulation pumps or wells, are used to bring up the water. A downhole consists of two types that are lineshaft pump systems and submersible pumps. Just as both of the types have been in practice for a long period back, the lineshaft pumping system is preferred over the submersible pumps. This is because it is affordable and submersible pumps require 800 feet of dept for the setting. 

Direct Heating

Source: EnergySage

Furthermore, A mechanical facility that is the transmission pipeline, heat exchanger, and the cooling system directs the necessary heat to its intended use. The transmission pipeline can either be a single pipe or a two-pipe system. The single pipe is a once-through system where the vapor is disposed of after use. This is generally preferred when geothermal energy is overflowing and when the water is pure or clean. And the two-pipe system recirculates the vapor where the residual heat is conserved. 

Now the heat exchangers used in the geothermal systems are the plate with a mechanical seal held in a frame by clamping rods, shell and tube, and downhole types. Yet the cooling is gained by using lithium bromide and ammonia absorption refrigeration systems. Afterward, The cooled water is stored in ponds through a disposal system. 

  • Geothermal Heat Pump

According to the Environmental Department of Canon Global, there are two different wells dug for this energy storage system. One of the underground wells is for cold water whereas another one is for warm water. Although different wells are dug, both of them are connected to an aquifer. So when in summer the building is cooled from the cold aquifer and in winter the heat is transferred through the hot aquifer. 

Cold water well and Warm water well

Source: Environment Department of Canon Global

The aquifer is operated differently. The heat present in the building will be transferred to the water. That will warm the water then the warmed water will be stored in well. In winter, that warm water will be used to heat the building because the warm water beneath will produce the heat. 

  • Geothermal Power Plants

A Power plant either be fueled by coal, gas, nuclear power, or this energy, all of these features produce electricity through heat or steam. The Geothermal Power Plant uses hydrothermal resources that may be turbines, generators, transformers, and other standard power generating power to turn heat into electricity. It required an exclusively high temperature of at least 300°F to 700°F coming from dry steam wells or hot water wells. Further, the wells are dug 1-2 miles deep into the surface and then people use the piping the steam or hot water technique. This powers a turbine that generates electricity. Again such power plants are usually found nearby hot springs, geysers, and volcanic erupted areas. 

Geothermal Power Plant

Source: A Student’s Guide to Global Climate Change

First, the hot water is pumped from the deep underground through a well with high pressure. After the water reaches the surface, the pressure is dropped. The pressured water will be warmer which allows the water to turn into steam. The turbine is spun by the steam. It is connected to a generator. On the whole, the generator assists in producing electricity by sending an electrical current to a step-up transformer outside the power plant. Voltage is increased in the transformer and the current is transmitted over the power lines to buildings. The process doesn’t end here instead the steam cools off in a cooling tower and consolidates back to the water. The chilled water is withdrawn again into the Earth to start the process again.

In contrast, the World's largest geothermal plant is the Geysers Geothermal Complex of the US. It has a total capacity of 1,517 MW. It is made up of 22 power plants and spread over several kilometers North of San Francisco. It lies on the tip of deep magma that stretches over 30 square miles. Likewise, the second largest is taken with Larderello Geothermal Complex, Italy. It comprises 34 plants with a total net capacity of 769 MW. Then Cerro Prieto Geothermal Power Station of Mexico features 4 plants and has 720 MW energy remarks as the third-largest Power Plant in the world. 

Types of Geothermal Power Plant

  • Dry Steam Power Plant

Dry Steam Power Plant

Source: US Department of Energy, Energy Efficiency, and Renewable Energy

There are three main types of Geothermal Power Plants: Dry Steam Plants, Flash Cycle Steam Plants, and Binary Cycle Plants. The Dry Steam Plants use steam naturally produced from the ground. The steam comes from the production of the well to turn the generator turbines. This is only possible at the places having the highest temperatures. The temperature varies from 212°F to 608°F.  However, it requires less vapor but the extracted water will be in the form of gas. The first geothermal power generation plant from a dry steam power plant was constructed in Italy in 1904. This had the power of 250 Kilowatt. 

  • Flash Steam Power Plant

Flash Steam Power Plant

Source: US Department of Energy, Energy Efficiency, and Renewable Energy

In the same way, Flash Cycle Steam Plants doesn’t use steam directly from the earth to generate electricity. Rather it pumps hot water at high-pressure below the earth. This is done through the well into the flash tank that is kept at a lower pressure. Due to the flash tank’s low pressure, the hot pressure turns into steam. Then the steam will spin the turbines and generate electricity. Here the water must be over 356°F. This is the widely practiced type of plant in the present context. In the end, the cooled water returns to the underground water tank to be heated by geothermal rocks again. 

  • Binary Cycle Power Plant

Binary Cycle Power Plant

Source: US Department of Energy, Energy Efficiency, and Renewable Energy

The last one is Binary Cycle Plants, which transfers the heat from geothermal hot water to another liquid. The heat causes the second liquid to turn into steam which helps to drive the turbine generator. This is likely to be considered as the commonly used energy in the future. Also, it can be utilized under lower temperatures but the other two types can’t. This can be worked in between 224.6°F to 359.6°F. Instead of using the water and steam directly, Binary Cycle Plants use the heat from underground reservoirs to heat the second vapor with a low boiling point. Then it spins a turbine and generates electricity. It has a thermal efficiency of 10-13%.

Types of Geothermal Energy Systems

This energy system is an alternative to that source using high electrical energies. This system is efficient, environmentally friendly, easy to use, and affordable. It uses almost half less energy than other conventional heating or cooling systems. Though there are several options to choose from in types of these energy systems, the environmental needs and demands should be strictly observed. Firstly the types of geothermal energy systems are:

Closed Geothermal Loop System

The closed geothermal loop system is high energy efficient that distributes heat equally in the house by reducing the reliance on fossil fuels. The installation cost could be expensive but it can last up to 25 years+. Despite that, it absorbs the natural heat contained from the ground itself and then releases it to the particular house equally. The system combines a heat pump that draws water and antifreeze solution through an underground water pipe, buried at shallow depths in your yard. As it requires little maintenance, it provides warmth in a renewable way.

Closed Geothermal Loop System

Source: Green Match

  • Horizontal Ground Source of Heat Pump

It requires larger space as two pipes need to be buried parallelly in a maximum of 2 meters down the horizontal trenches. The advantage of this type of Earth loop installation is that there is more pipe per meter used in a smaller trench area making it a more compact design for smaller gardens or plots. However, the disadvantage is that the heat resource can be easily removed from a much smaller footprint. This results in less heat extraction from the ground.

  • Vertical Ground Source of Heat Pump

Identically, a vertical ground source of heat pumps is costlier than the horizontal ones but it can be installed in a restricted area too. And this option doesn’t need larger pipes too because the requirement of a drilling rig to drill boreholes is about 80 meters deep. The disadvantage of a vertical ground source heat pump is that depending on the quality of the water being used from the well, water filters and periodic cleaning of the heat exchanger might be necessary inside. 

Open Geothermal Loop System

The Open Geothermal Loop system works by pumping the groundwater from an aquifer or similar and carrying it to the heat pump. That means the evaporator transfers its heat. After that, the water is either re-injected into the ground or discharged at the surface. Thus, the heat source is similar to the fluid that runs by the circuit, and it has to be replaced persistently because it is not re-circulated. The advantage of the system is that it is comparatively affordable than the other system.

  • Closed Loop System for Pond/Lake

This type is possible where there is an adequate amount and deep water is present. A pipe is settled underground from the location to the pond/lake so that the freezing winter doesn’t bother all. While it is more expensive to install than the open-loop system, it eliminates the continuous intake of well water. As in the case of any closed-loop system, there are no harmful effects on the environment.

Advantage of  Geothermal Energy

The advantages of using this energy are as follows:

  • Reliable

Unlike solar and wind energy, this energy doesn’t fluctuate. The energy is available always which means there is no requirement of depending on other factors to generate the power. So the process of calculation is simple and the outcome can be easily predicted. 

  • Environmental friendly

Though this energy is withdrawn from the beneath of earth, the fields produce no emissions. The carbon footprint of the geothermal power plant is minimal on which it releases 99% less carbon dioxide for every megawatt-hour of electricity it generates. There might be other polluting aspects but that seems to be less than other resources produce. For example, the free hot water and electricity production doesn’t make noise pollution.

  • Massive potential holder

According to data by Learn Mechanical, The power plants distribute 12.7 GW of electricity while every other resource delivers 17 Terawatts worldwide. In insomuch, it is estimated that geothermal power plants have the potential of 0.035 to 2 TW. After that, geothermal heat pump systems use 25% to 50% less electricity than conventional systems for heating or cooling, requiring less space for types of, and it is inexpensive too. Considering that there is a huge potential for this energy generation.

  • Great for heating and cooling

Energy plays a significant role in heating and cooling. Icelanders have been using this facility for a long time back. This doesn’t require a higher temperature but the steam in between the surface and well-dug of just 2 meters can be enough. This will help in heating and cooling the building or houses which increases the homeowner’s savings.  

  • Renewable and sustainable

This is the natural resource that will be accessible till the planet is destroyed completely. Plus, it is independent while comparing to other resources. According to scientists, geothermal reservoirs are expected to last for billions of years. Fossil fuels are meant to have an expiry date, in whatever way this energy has no limitation of ending. This makes the power both renewable and sustainable. 

  • Rapid Evolution

This era has introduced unexpected technologies to improve every dimension of each field. Similarly, technologies for exploiting natural resources have been created too. It shows that the trend of growth in this field is increasing. Hence, Indonesia and the Philippines are constructing a massively huge power plant for a better future.

Disadvantages of Geothermal Energy

Nevertheless, every part belonging to the universe has both pros and cons. Likewise, this energy is a definite environmentally friendly resource but some aspects do certain harm in our surroundings. To know more about the disadvantages, the following points have been explained thoroughly.

  • Environmental Issues

According to the Union of Concerned Scientists, there are plenty of greenhouse gases located underneath the earth. Whenever this energy is used, some of the greenhouse gases escape towards the ground and into the atmosphere. Besides, the emissions tend to be higher while comparing to geothermal power plants. It is because the power plants generate a lesser amount of sulfur dioxide and silica emissions. 

Thereupon the reservoirs can be detected of toxic heavy metals including mercury, arsenic, and boron. The pollution associated with geothermal power is very low, and just a tiny fraction of what we see with coal power and fossil fuels. Furthermore, there have been no reported cases of water contamination from geothermal sites in the US.  

  • Higher initial cost 

Though the energy provides free heat production, the initial capital costs tend to be higher. This is because the cost of drilling wells for the underground waterbody is expensive. Besides, there is a necessity to install the heating and cooling system which is way more costly than drilling the wells. The reason for the expensiveness is the advancement of the installation of technologies. For instance, an installation of a general heating pump might cost about $10,000-$20,000. The Return On Investment is predictable for sure but it will consume a long time. 

  • Preferable in certain areas 

This energy is specifically extremely hot under surface areas. Nonetheless, the hot rock should be suitable enough to dig the wells. Every type of rock won’t help in digging the well whereas the hot bearing capacity also differs from one another. Generally, such places are located away from the city where there is less population. Or it can be observed as the most volcanic erupted places are suitable for the huge production of energy. 

People normally neglect frequent natural calamities occurring in places. Thus, overproduction could harm the environmental issues because the necessity is at a populated place. 

  • Cause surface instability

When a surface is drilled, there is a possibility of causing the surface to unstable and trigger an earthquake. The traditional geothermal power plant construction requires drilling hot rock. Those contain trapped water or steam in their opening spaces and natural explosion. When these splits are divided by a drilled hole, the trapped water explodes as steam.

The drilling itself may not trigger earthquakes, but the rupturing of steam and subsequent return of the used water to the hot water reservoir could. The cycle leads to uncertainty along bursting lines that might result in an earthquake.

  • Experience dry spell

Geothermal heat approaching from the waterbody beneath may die down or run out of steam even after years of usage. The scarcity of every aspect needed for land may last decades, which is why it’s recommended to use the heat prudently and not abuse it. Incompatible use can also result in an impoverished distribution of heat.


The practice of this energy has existed for ages, rapidly increasing over the last three decades, for both uses of generating electricity and direct use of heat. At the outset, the efficiency of a geothermal system is only 20% but that is common among power generation facilities. The environmental impacts of the energy facilities are less than any other natural resource. It produces no emissions with 99% less carbon dioxide to mass-produce electricity. 

For instance, Wells of at least a mile deep or more are drilled into underground reservoirs to get connected with the geothermal resources. These resources can be exploited from naturally occurring heat, rock, and water or through enhanced geothermal systems, which enhance or create geothermal resources through a process called hydraulic stimulation. These geothermal resources, whether natural or enhanced, drive turbines linked to electricity generators and produce heat. 

In winter, a geothermal heating pump system can upgrade the temperature of the upper 3 meters of the Earth’s land. This happens when the heat is extracted from the houses and transferred to the cooler ground in the summer. Geothermal water from deeper in the Earth can be used directly for heating homes and offices, or growing plants in greenhouses. Some U.S. cities usually place the geothermal hot water energy’s pipe under roads and sidewalks to melt snow.

Exponentially, this energy is taken as being too practical from an economic viewpoint. It is considered a cheap, never-ending resource, and a base-load generator. However, the geothermal power plant isn’t cheap to install. It requires advanced technologies and manpower before the heavy Return on Investments. Well, the first country to use the prospects of Geothermal energy is Italy in 1904. Similarly, it is believed that the monkeys of Japan used this method from hot springs. The motive was to keep itself warm during winter. Today, the United States is the largest producer owning the World’s largest geothermal development is located at the Geysers North of San Francisco, California. 

We hope you have enjoyed our content on Geothermal Energy. Do you think we missed something? Do you know of some other way this energy contributes worldwide? Feel free to comment below. We always appreciate your suggestions.